Patton-electronic 2510RC Bedienungsanleitung

USERMANUALMODEL 2500RC SeriesModels 2500RC, 2510RCand 2520RC:All-Rate CSU/DSURack Mount CardSALES OFFICE(301) 975-1000TECHNICAL SUPPORT(301) 975-1007h

DTE Data FormatChoosing option 5 in the Software Switch Menu takes you to theData Format Menu (below). This option controls whether an async-to-sync

DSR Status During Local LoopbackChoosing option 6 in the Software Switch Menu takes you to theDSR Loop Status Menu (below). This option controls the

2122Set this option as follows:• Internal (Master): To use the Model 2500RC and 2520RC internalreference clock as the timing source, select item 1. U

3.3 REAR CARD CONFIGURATIONThe Model 2500RC Series has two interface card options: theModel 1000RCM12548 (DB-25/RJ-48S) and the Model1000RCM13448 (M

2526SGND & FRGND (JB4)In the connected position, this strap links DB-25 pin 7 (SignalGround) and frame ground. In the open position, pin 1 is “li

27 28Switching the Power Supply On and OffThe power switch is located on the front panel. When plugged inand switched on, a red front panel LED will

29 30• “CTS” will glow green to indicate an On condition. When on,the unit is ready to send data. If CTS remains off, check theForced RTS, Circuit As

31 325.2.2 Displaying Line/Loop StatusTo check the current status of the Model 2500RC Series and theassociated circuit, go to the Main Menu and selec

33 345.3.2 Remote Digital Loopback (RDL)The Remote Digital Loopback (RDL) test checks the performance ofboth the local and remote Model 2500RC Series

35 365.4 THE V.52 BER TEST PATTERN GENERATORThe Model 2500RC Series has a built-in test pattern generator anddetector. It can be invoked at both end

TABLE OF CONTENTSSection Page1.0 Warranty Information ...21.1 Radio and TV Interference1.2 F

Read Stored NumberSelecting item 2 in the Dial Menu lets you view the phone numbercurrently stored in the Model 2500RC Series non-volatile memory.Dial

39APPENDIX BCABLE RECOMMENDATIONSThe Patton Model 2500RC Series operates at frequencies of 20kHzor less and has been performance tested by Patton tech

41APPENDIX DINTERFACE PIN ASSIGNMENTDDS INTERFACEThe DDS Interface is an RJ-48S modular jack.Pin # Signal1 TX+2 TX-3 no connection4 no connection5 no

Dear Valued Customer,Thank you for purchasing Patton Electronics products! We doappreciate your business. I trust that you find this user manual he

1.4 SERVICEAll warranty and nonwarranty repairs must be returned freightprepaid and insured to Patton Electronics. All returns must have aReturn Mat

2.3 SUPPORTED APPLICATIONSThe Model 2500RC Series includes three units: the Model 2500RCAll-Rate CSU/DSU, the Model 2510RC Switched 56 CSU/DSU and th

3.1.1 Switch Set “S1”The configuration switches on switch set S1 allow you to specifyLine Rate, Circuit Assurance, RTS, Character Length, Data Format

Switch S1-4: Circuit AssuranceThe transmitter and the CTS output can be configured to go Ononly when a working communication circuit is established.

Switches S2-1, S2-2 and S2-3: Rate Adapter/DTE RateThe Model 2500RC Series includes a rate adapter that allows theunit to be used with DTE devices th

3.1.4 Setting Rotary Address SwitchesIf you plan to use the software control port to configure or dial theModel 2500RC Series unit, you will need to

3.2.3 Verifying Software Switch ControlIn order to use software switches for configuration, it is necessaryto disable the hardware switch settings.